For light duty spray-down applications, attach these wash guns to any standard garden hose.

The powerful combination of air and water creates a high-velocity, atomized spray without needing high pressure. These guns also can be used to siphon.

These wash guns have a high maximum pressure, so use them with pressure washers and high-pressure spray systems.

Clean hard-to-access areas by extending the reach of your quick-disconnect wash gun.

Clean and sanitize surfaces with the power of steam—with or without detergents and other chemicals.

Also known as air-shield and safety-shield nozzles, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.

Made from rubber, these nozzles won’t scratch or damage sensitive workpieces.

Control consumption and noise by adjusting the airflow.

The extra length allows access into hard-to-reach areas.

Focus air with pinpoint precision.

These nozzles are made of FDA-listed materials.

Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles.

Air blows out of these flat nozzles in a wide pattern at a 90° angle from the inlet, distributing air over a wider area than focused-airflow nozzles. They’re FDA compliant 21 CFR 110.40 for use in the food industry.

As compressed air flows through these nozzles, they rotate to efficiently and evenly blow off large areas.

Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.

The magnetic base mounts to your work surface and has a control valve for adjusting airflow.

Shaped to fit into extremely tight spaces, these nozzles can be used to remove parts from molds. Tap the wedge into position, attach the nozzle to a blowgun, and activate the airflow to release the part.

Blow debris and sweep it away with the built-in brush.

Twist the barrel to adjust water flow.

Use the lever to turn water flow on and off.

Control the flow while dispensing diesel fuel with these nozzles.

Nozzles allow you to control the flow while dispensing hydraulic fluid.

Slide the barbed end of these swivels into your dispensing hose and connect with a clamp. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.

These nozzles produce a flat, thin spray pattern. They're good for general cleaning, washing, etching, foam control, and applying coatings.

Drill a hole anywhere along a pipe and snap on these nozzles. Spray tips can be quickly and easily removed for cleaning and replacement.

Spray is deflected at a narrow angle to create the highest impact of all our flat spray nozzles.

A quick-disconnect hose fitting on these nozzles means you can remove and replace them easily to change spray patterns and angles.

Particles in liquid won’t clog these nozzles because of their unique internal and external design.

These nozzles project their spray at a right angle from their threaded connection.

Save time in applications where you often need to replace worn nozzles. These nozzles consist of a base and a nozzle, so you can replace the tip with just a quarter turn.

With a unique internal and external design, these nozzles let particles in liquid pass through instead of clogging.

A wide spray angle provides a larger coverage area and produces a finer, more atomized spray than full-cone nozzles.

These nozzles provide a uniform distribution of droplets.

Fogging nozzles provide smaller, more atomized spray droplets than misting nozzles.

Create small, atomized spray droplets for cooling, moistening, and humidifying applications. These nozzles have a check valve that prevents dripping when they’re turned off

By circulating their spray, these nozzles clean faster with more even coverage and less water than stationary tank-washing nozzles.

Use these nozzles with detergent that’s diluted in water to create a rotating, multi-directional foam spray for effectively rinsing tanks, drums, and small vessels.

Avoid clogs while rinsing tanks, drums, and small vessels. These nozzles have a unique internal and external design, so particles in liquid pass through instead of getting stuck.

Spray a precise, concentrated, high-velocity stream longer distances than flat spray nozzles to handle tough cleaning applications.

The superior cleaning ability of a solid stream has been combined with rotating spray action for excellent coverage.

Push the nozzle out for lower pressures and pull it back for higher pressures. Turn the cover to adjust the spray angle from 0° to 25° or 75°.

Spray a precise, concentrated, high-velocity stream longer distances than flat spray nozzles to handle tough cleaning applications.

No need to switch between nozzles—push these nozzles in and pull them out to change their pressure level, and twist their cover to adjust the spray angle between 0° and 40°. Their quick-disconnect hose connection makes attaching and removing them easy.

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

Use with Loc-Line hose to assemble and disassemble components.

These nozzles handle coolant pressure up to 150 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Draw coolant from your existing tank.

Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.

These dispensers have a reservoir and controls for coolant flow.